推荐产品
质量水平
包装
pack of 10 slides
pack of 25 slides
表面电阻率
8-12 Ω/sq
长度 × 宽度 × 厚度
75 mm × 25 mm × 1.1 mm
透射比
>83%
折射率
n20/D 1.517 (lit.)
SMILES字符串
O=[Sn]=O.O=[In]O[In]=O
InChI
1S/2In.5O.Sn
InChI key
LNNWKAUHKIHCKO-UHFFFAOYSA-N
正在寻找类似产品? 访问 产品对比指南
一般描述
应用
已报道的一些其他用途有：
- 在ITO封闭的玻璃基片上制备的真黑素样品。
- 用于光束偏转（OBD）传感的液体池的界面窗口含有一层20nm厚的氧化铟锡膜。
- 介孔TiO2 膜是在ITO导电玻璃上形成的
物理属性
当暴露于300℃的温度30分钟或更长时间时，电阻可以增加到高达30 Ω。
储存分类代码
13 - Non Combustible Solids
WGK
WGK 3
闪点(°F)
Not applicable
闪点(°C)
Not applicable
个人防护装备
dust mask type N95 (US), Eyeshields, Gloves
Which document(s) contains shelf-life or expiration date information for a given product?
If available for a given product, the recommended re-test date or the expiration date can be found on the Certificate of Analysis.
How do I get lot-specific information or a Certificate of Analysis?
The lot specific COA document can be found by entering the lot number above under the "Documents" section.
How do I find price and availability?
There are several ways to find pricing and availability for our products. Once you log onto our website, you will find the price and availability displayed on the product detail page. You can contact any of our Customer Sales and Service offices to receive a quote. USA customers: 1-800-325-3010 or view local office numbers.
What type of glass is Product 578274, Indium tin oxide coated glass slide, made of?
The slide is made with soda lime float glass. Molten glass is floated on a pool of liquid tin under a nitrogen/hydrogen atmosphere. This high volume process results in glass which does not require grinding or polishing to achieve a high-quality finish. Float glass will typically have a strain point of 523°C, a CTE of 77-85 x 107 / °C, and a refractive index of 1.517. Typical composition of float glass is 72.6% SiO2, 0.8% B2O3, 1.7% Al2O3, 4.6% CaO, 3.6% MgO, and 15.2% Na2O.
For Product 578274, Indium tin oxide coated glass slide, what is the passivation layer, and what is it's purpose?
ITO coated float glass is only offered with a SiO2 passivation layer applied directly on the glass prior to ITO coating. The passivation layer is intended to minimize the leaching of alkali oxides into liquid crystals, which can have a detrimental effect on the volume resistivity of the liquid crystal.
How do I clean Product 578274, Indium tin oxide coated glass slide?
To clean ITO slides, the manufacturer recommends to immerse the slides in a 20 weight % solution of ethanolamine in deionized water, heat to 80°C in an ultrasonic bath for 10-15 minutes. After this step, the slides should be removed and rinsed several times with deionized water, and finally dried with pure nitrogen gas to avoid water spotting.
What method can be used to etch Product 578274, Indium tin oxide coated glass slide?
Per the manufacturer, an aqueous solution of 20% hydrochloric acid, 5% nitric acid and a few drops of liquid detergent to promote wetting of the ITO surface will remove ITO. If this solution is heated to 55°C, it will typically etch 100 ohm ITO coating in 30-60 seconds, or if the etching is carried out at room temperature, it will take six to ten minutes. Differences in the morphology of the coating, the thickness of the coating (more conductive coatings will be thicker), and changes in the purity or concentration of the acid solution will effect the time required to remove the ITO. Please be advised that ITO coatings can be lost if they come into direct contact with mineral acids and strong organic acids. Therefore, direct contact with these agents should be avoided. After the etching process is complete, the slides should be immediately rinsed in a 10% aqueous solution of sodium carbonate to neutralize any residual acid. To avoid water spotting, blow dry the slides with pure nitrogen gas.
What is the Department of Transportation shipping information for this product?
Transportation information can be found in Section 14 of the product's (M)SDS.To access the shipping information for this material, use the link on the product detail page for the product.
My question is not addressed here, how can I contact Technical Service for assistance?
Ask a Scientist here.
商品
Organic Semiconductor Laser Materials
Professor Shinar highlights low-cost, disposable sensor configurations in organic and hybrid electronics for healthcare applications.
Organic photovoltaics (OPVs) represent a low-cost, lightweight, and scalable alternative to conventional solar cells. While significant progress has been made in the development of conventional bulk heterojunction cells, new approaches are required to achieve the performance and stability necessary to enable commercially successful OPVs.
A transparent conductive electrode (TCE) is an essential component of various optoelectronic devices such as solar cells, liquid-crystal displays (LCD), light-emitting diodes (LED), and touch screens.
实验方案
Selenium's roles range from essential dietary element to semiconductor in advanced applications like xerography.
我们的科学家团队拥有各种研究领域经验，包括生命科学、材料科学、化学合成、色谱、分析及许多其他领域.
联系技术服务部门